1. On the basis of the national standard DC charging pile, the equipment displays system circuits such as DC charging interface, DC charging harness, high-voltage battery pack, control board, electric energy meter, and contactor. Key signals can be measured, and key components and circuits can be faulted. To enable students to understand the control process of the DC charging system, that is, how to wake up the system, how to control the relay, and how to monitor the charging process.
2. The working status of the device can be judged by the color of the indicator light.
3. The training platform is equipped with a charging pile and a circuit schematic diagram of the vehicle control system. Trainees can understand and analyze the working process and control strategy by comparing the circuit diagram and the real object, and the system can perform fault setting.
4. An emergency stop switch is installed, which can stop the operation of the equipment with one button in case of emergency.
5. Arrange light-emitting diode strips in the protective layer of the high-voltage wiring harness. When there is current in the wiring harness, the LED strips will display the direction of the DC charging current.
6. The system is equipped with a Windows system touch all-in-one computer device of no less than 23.6 inches, with built-in charging system software, which can display information such as charging voltage, current, power consumption amount, and charging pile fault codes in real time.
7. Charging information interface: display charging system charging status, charging current, charger head temperature, charging voltage, CC1 voltage, insulation detection, vehicle BMS information, charging time, charging power, consumption amount, fault codes and other information in detail.
8. Start charging interface: We can choose automatic charging, charging according to the amount of electricity, charging according to time, charging according to the amount and other modes.
9. End charging interface: Swipe the card to end charging.
10. Fault query interface: The green and red status of the charging pile icon reflects the fault status of the charging pile, and the fault name is directly displayed in the fault state.
11. The charging system software has the functions of fault setting and data query, and can perform fault setting on circuits such as CC1 circuit, ammeter communication circuit, indicator light communication circuit, card reader grounding circuit, pulse electronic lock ELF circuit, and charging gun S+ circuit inside the charging system.
12. The main board of the charging system has CAN bus interface, electric meter communication interface, credit card billing communication interface, PC communication interface, insulation detection circuit interface, emergency stop detection interface, CC1 isolation measurement interface, gun seat temperature detection interface, gun lock control and detection Interface, DC contactor control circuit interface.
13. The training platform is equipped with a charging load device, which can be charged by simulating the load of the power battery pack through a high-power aluminum shell resistor. The normal charging process can be realized even if the charging pile is not connected to the vehicle. Simulate the load with 2 pieces of aluminum casing resistors and cooling fan for heat dissipation, with discharge currents of 2A and 4A respectively.
14. Equipped with a vehicle-side signal communication module and a data display, it can display the charging stage status, demand voltage, demand current, maximum charging voltage, maximum charging current, charging mode, current power SOC value, output voltage, and output current of the charging pile in real time. , output power, accumulated power, BMS parameter setting, charger parameter display and other functions.
15. Equipped with wireless fault-setting system by tablet, at least 10 faults.
16. Supporting electric vehicle charging system teaching software: explain the principle of electric vehicle DC charging through 3D animation models and circuit principles, and clearly show the structure of each component. And it is equipped with after-school exercises to strengthen students' understanding of relevant knowledge.
17. The training platform is equipped with 4 lockable casters, which are convenient for moving and fixing the equipment.
1. Dimensions (mm): 1600 × 700 × 1760 (length × width × height)
2. Input power: AC220V±10% 50Hz
3. Working power supply: DC12V/100V
Leakage protector, AC contactors, charging load simulator, AC/DC power supply control system, national standard DC charger, national standard vehicle charging stand, emergency stop switch, card swiping module, switching power supply, aluminum shell load resistor, shunt, electric energy meter, main control module of DC charger, 7-inch touch display screen, 23.6-inch touch all-in-one device, charging system teaching software, LED light strip, USB distributor, indicators control module, wireless fault-setting system.