FXB-Z07002 Intelligent Sensor Installation and Commissioning Training Bench

About Feature Technical Parameter Basic Configuration

Intelligent sensor installation and commissioning training bench is a special equipment that can be used for theoretical teaching, training and assessment based on the connected teaching vehicle testing assessment standard. The training bench has deployed the millimeter wave radar, ultrasonic radar, LIDAR, vehicle camera, combined navigation and drawing circuit wiring process diagrams of various sensors to achieve principle introduction, structure display, assembly, wiring, commissioning, fault diagnosis, data testing and assessment functions. The training bench is also equipped with a dedicated laptop to install the original factory driver and debugging software of intelligent sensors, which is convenient for quality detection of intelligent sensors and identifies the models and interface types of different intelligent sensors. It makes it easier for students to master the installation and commissioning ability, fault analysis and processing ability. Applicable to the teaching needs of medium and higher vocational and technical colleges, ordinary education colleges and training institutions to test and assessment of intelligent connected cars' intelligent sensor.

1. Camera module: equipped with camera circuit diagram, students can connect the camera circuit against the circuit diagram, and carry out driver installation and quality testing of the camera via PC terminal. According to the process document, the camera can be installed on the intelligent network teaching vehicle for teaching assessment.
2. Millimeter wave radar module: equipped with millimeter wave radar circuit diagram, students can connect the circuit of millimeter wave radar according against the circuit diagram, and carry out driver installation and quality test of millimeter wave radar through PC terminal. According to the process document, millimeter wave radar can be installed on the intelligent network teaching vehicle for teaching assessment. 3. Lidar module: equipped with LIDAR circuit diagram, students can connect the circuit of LIDAR against circuit diagram, and carry out driver installation and quality test of LIDAR through PC terminal. According to the process document, LIDAR can be installed on the intelligent connected teaching vehicle for teaching assessment.
4. Ultrasonic radar module: equipped with ultrasonic radar circuit diagram, students can connect the circuit of ultrasonic radar against circuit diagram, carry out driver installation and quality test of ultrasonic radar through PC terminal. According to the process document, ultrasonic radar can be installed on the intelligent connected teaching vehicle for teaching assessment.
5. GPS combination inertial navigation module: equipped with GPS combination inertial navigation circuit diagram, students can connect the circuit of GPS combination inertial navigation against circuit diagram, carry out driver installation and quality test of GPS combination inertial navigation through PC terminal. According to the process document, GPS combination inertial navigation can be installed on the intelligent connected teaching vehicle for teaching assessment.

Equipment size(mm): not less than 1600 x 800 x 1700(length × width x height)
1. 1 piece of LIDAR.
Horizontal view angle: 360°.
Vertical view angle: 31° (-16 ° ~ +15 °)
Distance measurement: 0.3~80m (10% reflectivity)
Distance measurement accuracy: ±5cm (0.3~1m), ±2cm (1~80m)
Distance measurement channel: 16 lines
Provide 100 megabit Ethernet data output, including distance, rotation angle, reflectivity and other information
Operating temperature to meet: -20 ℃ -65 ℃
Working voltage: 9-32V
Protection level: not less than IP67

2. 1 piece of medium range millimeter wave radar.
Operating frequency: 77GHz
Modulation mode: FMCW
Transmit power: 10dBm
Distance measurement range: 1m~160m
Distance measurement accuracy: ≤0.3m
Speed range: 180km/h
Speed measurement accuracy: <0.5km/h
Maximum number of detection targets: ≥30
Maximum azimuth coverage: 45°
Pitch angle coverage: ±5°
Detection cycle: 50ms
Power consumption: 7W
Weight: ≤300g
Waterproof rating: IP67

3. 1 piece of ultrasonic radar.
Distance detection: 0.1m - 3.5m.
Detection distance accuracy: ±5cm.
Probe integrated RS232 serial data output.
Operating temperature: -40 ° C - 85 ° C.
Operating voltage: 9-16V.
Protection level: IP67.

4. 1 piece of Camera .
Lens type: Fisheye
Photographic film: IMX291 (1/2.8 inch)
Maximum effective pixels not less than: 1920 (H) * 1080 (V)
Signal-noise ratio: 42dB
Dynamic range: 72dB
Sensitivity: 1.8V/lux-sec@550nm
Minimum illumination: 0.2lux
Interface Type: USB3.0 High Speed
Adjustable parameters: brightness, contrast, color saturation, hue, sharpness, gamma, white balance, backlight contrast, exposure
Power supply and interface: USB BUS POWER 8P-3.0mm socket
Voltage: DC5V
Current: 150mA-200mA

5. 1 piece of GPS combination navigation.
GNSS signal tracking: GPSL1&L2, GLONASS, GALILEO, BEIDOU, SBAS, DGPS, RTK
Speed accuracy: 0.03m/s RMS
Output rate: combination navigation data 1-200 Hz
Horizontal positioning accuracy: ±1.2m RMS L1&L2, ±0.4m RMS DGPS, 0.01+1ppm RMS RTK
Heading accuracy: 0.1°

6. Laptop
CPU series: i5 and above
Number of cores/threads: quad-core and above
Memory capacity: 6GB or more
Hard disk capacity: 256GB or more
Video memory capacity: 2GB or more
1 Ethernet interface
1 HDMI HD interface
2 USB interface or more